Log in or Sign up
Coin Talk
Home
Forums
>
Coin Forums
>
Ancient Coins
>
Question for seasoned Slab-Crackers
>
Reply to Thread
Message:
<p>[QUOTE="lordmarcovan, post: 3067942, member: 10461"]OK, here you go- several paragraphs and some extra commentary about a simple technique that can be performed in far less time than it will take you to read this post:</p><p><br /></p><p><b><font face="Georgia"><font size="5">The LordM "No Tools" Slab-Cracking Technique</font></font></b></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">Essentially my technique consists of inserting the top portion of the slab (the part where the label is) between two fixed, immovable, and sturdy surfaces like a gap between the boards on a porch or deck, and then pushing the slab with one's foot to "bend" it, exerting pressure in one direction. The placement of the slab between the boards means that while you're exerting pressure on it, you're "bending" it until it snaps in two, breaking off that top portion where the label is. The gap between the boards becomes your fulcrum.</font></font></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">Once you've done that, and the top portion (label part) of the slab is snapped off, the remaining plastic can usually be pried apart without too much difficulty, though one does need to be wary of jagged plastic shards if you didn't get a clean break. This is why I recommend pushing on it with a <i>shoed</i> <i>foot</i>. That keeps your eyes and other body parts well above the breaking plastic. A flathead screwdriver and/or some pliers can be helpful for the final plastic separation and removal, and I do recommend gloves for that, but this is mostly a "no tools" method.</font></font></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">Obviously if you have a workbench and a vise and tools and all that, it is better, but this method occurred to me while I was at a show and needed to do a quick crackout with <i>no</i> tools on hand. It is crude and <i>looks</i> brutally primitive, but it is quick, easy, and effective, and actually less risky for the coin than if the slab were subjected to hammering (and hammering can create flying shrapnel, which is never good). Since the coin remains sandwiched between the two halves of the lower part of the slab, it stays protected.</font></font></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">It takes only a second or two. *<b><i>snap</i></b>!* I've even done it between a door and the door frame before, though that only works with a reasonably heavy metal door. Anywhere there is a gap between two solid, immovable surfaces that is wide enough and deep enough to insert the slab, but narrow enough to create a fulcrum (a half-inch gap between the boards in a deck is ideal), you can snap a slab in seconds, pry apart the remnants, carefully extract the coin, pick up the plastic pieces, and be on your way.</font></font></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">My World Coin buddies from the 2006 FUN show cracked many jokes about my method (get it? <i>cracked?</i> haha), but it works, and I've used it ever since. [USER=81808]@Aethelred[/USER] witnessed the first time I did it.</font></font></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">It is so simple, you might find yourself saying, <i>"Aw, man, I was overthinking this all along."</i></font></font></p><p><font face="Georgia"><font size="5"><br /></font></font></p><p><font face="Georgia"><font size="5">Oh- and the slabbed coin I pioneered this technique on? A 1904 USA $20 Liberty, PCI MS62. Cracked it, submitted it to PCGS raw at the show, and it came back MS64, bringing me nearly a $1,000 profit when I later resold it. That remains my best cherrypick thus far.</font></font>[/QUOTE]</p><p><br /></p>
[QUOTE="lordmarcovan, post: 3067942, member: 10461"]OK, here you go- several paragraphs and some extra commentary about a simple technique that can be performed in far less time than it will take you to read this post: [B][FONT=Georgia][SIZE=5]The LordM "No Tools" Slab-Cracking Technique[/SIZE][/FONT][/B] [FONT=Georgia][SIZE=5] Essentially my technique consists of inserting the top portion of the slab (the part where the label is) between two fixed, immovable, and sturdy surfaces like a gap between the boards on a porch or deck, and then pushing the slab with one's foot to "bend" it, exerting pressure in one direction. The placement of the slab between the boards means that while you're exerting pressure on it, you're "bending" it until it snaps in two, breaking off that top portion where the label is. The gap between the boards becomes your fulcrum. Once you've done that, and the top portion (label part) of the slab is snapped off, the remaining plastic can usually be pried apart without too much difficulty, though one does need to be wary of jagged plastic shards if you didn't get a clean break. This is why I recommend pushing on it with a [I]shoed[/I] [I]foot[/I]. That keeps your eyes and other body parts well above the breaking plastic. A flathead screwdriver and/or some pliers can be helpful for the final plastic separation and removal, and I do recommend gloves for that, but this is mostly a "no tools" method. Obviously if you have a workbench and a vise and tools and all that, it is better, but this method occurred to me while I was at a show and needed to do a quick crackout with [I]no[/I] tools on hand. It is crude and [I]looks[/I] brutally primitive, but it is quick, easy, and effective, and actually less risky for the coin than if the slab were subjected to hammering (and hammering can create flying shrapnel, which is never good). Since the coin remains sandwiched between the two halves of the lower part of the slab, it stays protected. It takes only a second or two. *[B][I]snap[/I][/B]!* I've even done it between a door and the door frame before, though that only works with a reasonably heavy metal door. Anywhere there is a gap between two solid, immovable surfaces that is wide enough and deep enough to insert the slab, but narrow enough to create a fulcrum (a half-inch gap between the boards in a deck is ideal), you can snap a slab in seconds, pry apart the remnants, carefully extract the coin, pick up the plastic pieces, and be on your way. My World Coin buddies from the 2006 FUN show cracked many jokes about my method (get it? [I]cracked?[/I] haha), but it works, and I've used it ever since. [USER=81808]@Aethelred[/USER] witnessed the first time I did it. It is so simple, you might find yourself saying, [I]"Aw, man, I was overthinking this all along."[/I] Oh- and the slabbed coin I pioneered this technique on? A 1904 USA $20 Liberty, PCI MS62. Cracked it, submitted it to PCGS raw at the show, and it came back MS64, bringing me nearly a $1,000 profit when I later resold it. That remains my best cherrypick thus far.[/SIZE][/FONT][/QUOTE]
Your name or email address:
Do you already have an account?
No, create an account now.
Yes, my password is:
Forgot your password?
Stay logged in
Coin Talk
Home
Forums
>
Coin Forums
>
Ancient Coins
>
Question for seasoned Slab-Crackers
>
Home
Home
Quick Links
Search Forums
Recent Activity
Recent Posts
Forums
Forums
Quick Links
Search Forums
Recent Posts
Competitions
Competitions
Quick Links
Competition Index
Rules, Terms & Conditions
Gallery
Gallery
Quick Links
Search Media
New Media
Showcase
Showcase
Quick Links
Search Items
Most Active Members
New Items
Directory
Directory
Quick Links
Directory Home
New Listings
Members
Members
Quick Links
Notable Members
Current Visitors
Recent Activity
New Profile Posts
Sponsors
Menu
Search
Search titles only
Posted by Member:
Separate names with a comma.
Newer Than:
Search this thread only
Search this forum only
Display results as threads
Useful Searches
Recent Posts
More...