Going though some old boxes today I found a few items thay had fallen off the radar. Now I can pretty much tell you a little something about most all the coins in my collection. But I found this blank platchet That is just a tad bit over 23 mm & its 6.22 g. Weight. Its a copper alloy...and if not what I expect it could be...it's definitely a blank for a world coin that fits the weight ,and size... My thoughts is that it is a blank for a US two cent pc. As its weight is spot on for the 2 cent 6.22 g. And if sent through a roll up mill to finish the edge I believe that it would fit on a two cent pc perfectly...and I can't find my caliber but its the same thickness as a 2 cent pc. Your thoughts? Now it may of been a blank that the mint used for mintage of a world coin. As the US does produce for other countries. See image next to a 1867 us 2 cent pc.
Definitely worth looking into if it matches perfectly. Here's a 2c blank: https://coins.ha.com/itm/errors/two-cent-piece-2c-type-one-blank-ms62-brown-pcgs/a/1344-4604.s and a 2c planchet: https://coins.ha.com/itm/errors/two...BrowseTabs-Auction-Archive-ThisAuction-120115 Maybe try to reach out to Fred Weinberg?
Copper punch out. Just a plug, It has an upset rim? Whats the weight? The collar cannot shrink the diameter of the coin.
Yours is very similar to mine, rounded on one side, flat with a small lip on the other. I was told a long time ago that it's just a punch-out. Mine is slightly smaller than a Fiji 1c at around 17.5mm. Check the edge on yours if its half smooth and half rough. Not sure where I got it but it's been in my junk box for ages. I tend to agree that it's a punch-out, from what I haven't a clue.
I dont believe that it is a punch out..as most ive ever seen and examine have a flat spot some where on the rim. The rim on this is smooth no flat area at all. The fact that its weight is spot on 6.22 g. Leads me to believe that its a 2 cent blank....or a blank for another copper from a world coin . Thanks for your input.
I'll reach out to Fred as he is the real expert on errors, I have a few connections through Coneca and we have talked severl times over the last 50 years. As a Coneca member, and contributing author for Error Scope Magazine.... there's a nice write up and interview with Fred part one of a two part interview....just hit my mail box this week. If your a Coneca member you will enjoy the article very much its a very good read...thanks for everyones input. Plus a plug for 4 more articles I've written to be in Error scope later this year. Thanks again.
Mine in hand edge is somewhat finished ,and correct it is rounded more on one side than the other ,but again why tool an edge on an blank piece of copper if just a punch out of sorts,and a piece of junk or waste? I trying to think back as to where I got this.... from that be a better clue to its porpose.
For what it's worth, here's the edge of mine, and sandwiched between a US wheat cent, Canadian cent, and 1982 Fiji cent. I agree that the punch-outs from a junction box etc typically have a burr.
Its smooth like in the image for 360 degrees round the coin... a slug as such would be useless in a vending machine....as they are set to reject anything like this..and the size wouldn't match a quarter... I know as a store manager many times I had to deal with machines in-store as well the pony ride out front. LoL
Your two cent piece pictured is 23 mm. The slug next to it is noticeably larger. A quarter is 24.26 mm. Take a picture of your slug atop a normal quarter. It's a slug meant to be used as a quarter. The edge does not matter in many vending machines. Denial is not just a river in Egypt.
Perhaps mine was meant to be a dime slug. I did not think to compare it with a dime since it's copper, but it's probably close to the 17.9mm diameter. Payphones used to be 10c, parking meters too maybe.